A true slipper seal, the Turcon® Glyd Ring® relies on the O-Ring to energise it and provide sealing force, at zero or low pressure. As the pressure increases, the Turcon® Glyd Ring® is energised by hydraulic pressure, forcing it against the sealing surface. A full range of sizes are offered to suit all MIL-G-5514F and AS4716 rod and bores.

O-Rings are available to meet ISO 3601, AS 568 and other recognized standards. Special sizes are also available. Large diameter O-Rings can be supplied using our FlexiMold™ process. At higher pressures, Trelleborg Sealing Solutions recommends O-Rings be used with Turcon® Back-up Rings.

O ring Seals 1. O-Rings and Back-up Rings Your Partner for Sealing Technology 2. Your Partner for Sealing TechnologyTrelleborg Sealing Solutions is a major international sealing Facilities are certified to ISO 9001:2008 and ISO/TS 16949:2009.force, uniquely placed to offer dedicated design and Trelleborg Sealing Solutions is backed by the experiences anddevelopment from our market …

The glands have been specifically designed for applications using SAE AS568 size O-Rings, with related class 2 tolerances, at pressures exceeding 1,500psi/ 10.3 MPa utilizing one or two anti-extrusion Back-up Rings and applications at pressures under 1,500psi / 10.3 MPa without Back-up Rings.

View O-Ring Tolerances, Molded Rubber Tolerances, Extruded Rubber Tolerances, and More. Proper gland design can typically allow for high performance sealing with lower cost general purpose tolerance parts. Specialty performance products and materials require even more attention to gland design adjustements for specific application environments ...

© Trelleborg Sealing Solutions. All rights reserved. Disclaimer | O-Ring Calculator (Build-Release-1.0)

** At pressures > 40 MPa use diameter tolerance H8/f8 (bore/rod) in area of the seal or consult TSS for alternative material or profiles. TSS Slydring®/Wear Rings are not applicable at very small radial clearance; consult the Slydring® catalog. *** O-Rings with …

This O-Ring Calculator is part of a suite of tools and apps from Trelleborg Sealing Solutions that includes the highly successful ISO Fits & Tolerances and Unit & Hardness. All are available at tss.trelleborg.com and apps are free from iTunes or via the Apple …

The O-ring calculator tool is intended to form the basis of an o-ring installation, and assist with selection of o-ring and hardware dimensions. Recommendations are based on available technical information, and are offered as suggestions only, any reliance placed on such information by …

PROSEALS USA provides o-rings and engineered sealing products, including PTFE, rubber o-rings, metal o-rings, Precix, Trelleborg, Parco, metal seals, and sealing products for critical applications and industrial customers such as automotive, oil and gas, chemical, and hydraulic industries. Visit us at prosealsusa.com or call 800.536.1098.

O-Rings are used in a variety of fields: they are either used as sealing elements or as energizing elements for hydraulic slipper seals and wipers. Thus, the O-Ring is basically used in every field of industry including aerospace, automotive or general engineering. Your Advantages. Today, the O-Ring is the most widely used seal because of its inexpensive production methods and its ease of use.

SAE International's AS568 standard specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-Rings used in sealing applications and for straight thread tube fitting boss gaskets. Using Trelleborg's new AS568 O-Ring brochure and e-Catalog, customers can easily find products and request a ...

O-Ring Search: Offers the selection of O-Ring nominal sizes according to the following national/international standards: ISO 3601, JIS B 2401 (Japan) SMS 1586 (Sweden). Calculate O-Ring tolerances: according to ISO 3601-1 Class B; Switch between metric and inch: units while your calculations adjust automatically with your selections.

Technical Handbook O-rings Size tolerances and surface imperfections on O-rings are influenced by the tolerance, finish, and cleanliness of the mold cavities from which they are produced. These tolerances have been specified in the Aerospace Standard AS 568A and AS 871 A, DIN Standard 3771 Part 3, ISO 3601 Part 3, and MIL-STD-413C.

Trelleborg Sealing Solutions is a leading global supplier of sealing solutions. Our range of products includes O-Rings, hydraulic seals, rotary shaft seals, oil seals, static seals, pneumatic seals, mechanical face seals and many more. Find out more about us in our company presentation film

Metric o-ring groove designs vary greatly and choosing the right one for your application is important for maximum o-ring performance. This metric o-ring groove design reference guide will help you find the right radius, back-up, pressure and other o-ring dimensions for basic applications.

Trelleborg Sealing Solutions announces the release of the O-Ring Calculator app. The app calculates O-Ring dimensions and tolerances, and recommends sizes and Trelleborg Sealing Solutions part numbers. Enter bore or rod/shaft diameter and receive an O-Ring recommendation and O-Ring housing calculation according to recommendations of ISO 3601.

For all O-Ring inside diameters d1 and cross sections d2 the tolerances according to ISO 3601-1, class B are valid. The appropriate tolerance values for each dimension are listed in the table ...

The glands have been specically designed for applications using SAE AS568 size O-Rings, with related class 2 tolerances, at pressures exceeding 1,500psi/ 10.3 MPa utilizing one or two anti-extrusion Back-up Rings and applications at pressures under 1,500psi / 10.3 MPa without Back-up Rings.

Shop our range of Trelleborg O-Rings & O-Ring Seals made from a wide choice of elastomer materials suitable for both standard and special applications. Buy quick and easy online!- ORAR00015-E7502. O-Rings - ORAR00015-E7 ... Inside diameter tolerance ...

Trelleborg Sealing Solutions has maintained the series as ... an O-Ring as energizing element. p O-Ring ... hardware tolerances and movement. Elastomer materials available to meet a wide variety of service conditions O-Ring Relief Chamfer Reduced seal load under pressure.

A standard quality O-Ring has dimensional tolerances to Trelleborg Sealing Solutions standard TBS-00024 according to ISO 3601-1, class B and standard surface quality according to …

The O-Rings and Back-up Rings catalog has been updated with four additional materials and adjusted sizes and tolerances based on AS568 for easier ordering. Simple in form, but not in function, the humble O-Ring is one of the most widely used seals in the world. Trelleborg Sealing Solutions continues to develop their offering with efficiency and ...

Trelleborg, Sealing, Solutions, digital, mobile, tools, app, o-ring, selector, engineering, design. contactusurl. Sealing Solutions. All Trelleborg sites Close. Group Trelleborg is a world leader in engineered polymer solutions that seal ... Engineered Coated Fabrics Trelleborg's Engineered Coated Fabrics business unit, ...

O-Rings are used in a variety of fields: they are either used as sealing elements or as energizing elements for hydraulic slipper seals and wipers.

The double acting Tucon ® Glyd Ring is a combination of a Turcon based slipper seal and an energising O-Ring. It is produced with an interference fit which together with the squeeze of the O-Ring ensures a good sealing effect even at low pressure. At higher system pressures, the O-Ring is energised by the fluid, pushing the Turcon® Glyd Ring®

O-Ring quality: Dimensional tolerances - Inside diameter, Cross section ISO 3601-1 is recommended; Surface quality ... The Trelleborg O-Ring Calculator is optimized for desktop devices but there is also an App version for mobile users. View the O-Ring Calculator here.

O-Rings. Trelleborg O-Rings are the most widely used seals because they are efficient and economical and can be used in a wide variety of static and dynamic applications. O-Rings can be used to seal practically all liquid and gaseous media and they are available in elastomeric and other materials including EPDM, FKM and NBR, among others.

The O-Ring is compressed in the radial direction when seated in the gland. Hence, one can think of the O-Ring cross-section as being pinched between the Bore Diameter B d and the Groove Diameter G d. In order for the O-Ring to be compressed when in the gland, its cross-section diameter CS must be greater than the total effective depth of the ...

O-Ring Calculator. The online O-Ring Calculator offers engineers and professionals a quick and easy way to calculate O-Ring dimensions and the appropriate housing layout in accordance with the international O-Ring standard ISO 3601. By simply entering installation specifications for an application, it recommends O-Ring sizes, housing layout and ...

The O-Rings and Back-up Rings catalog has been updated with four additional materials and adjusted sizes and tolerances based on AS568 for easier ordering. Simple in form, but not in function, the humble O-Ring is one of the most widely used seals in the world. Trelleborg Sealing Solutions continues to develop their offering with efficiency and ...

Android App on Google Play We understand the needs of engineers on the go. Check out our latest mobile tools and apps, ranging from an O-Ring calculator to unit and hardness converters. Just search for "Trelleborg" in the App Store or Google Play to find the tools to optimize your daily productivity.

The Trelleborg Sealing Solutions O-Ring App calculates O-Ring dimensions by simply entering installation specifications for your application in metric or inch. In addition, the App recommends O-Ring sizes according to ISO 3601, so you know exactly which part you need. ... - Tolerances: calculation of O-Ring tolerances according to ISO 3601-1 ...

ERIKS standard O-Rings. and load them also into your created design. info. chemical volume swell (%) cross section diameter (mm) ISO 3601. free. Calculate Results. Reset calculator.